Eddiecat send me a text and I'll text you pic of track & car I have for Nacra. Pete 909-800-5237

I probably have one. Will check on Nacra beam tomorrow. Pete 909-800-5237

You will have to go to the West ramp on the North Shore (only one open as water too shallow at East ramp& it's closed). There is lake fee of $25 & yo...

By 1973 I'd had 6 H-16's on Lake St Clair east of Detroit. Learned of the Prindle 16 and soon bought 3 sight unseen becoming Detroit dealer & eventua...

There's one here in San Diego craigslist with platform for $500 asking. PeteEdited by pbegle on May 17, 2016 - 09:14 PM.

Have a new Prindle jib halyard with sister clips ready to ship. $25 plus $8 shipping. If you don't have the plastic cleat on jib tack, just tie it t...

Have couple all aluminum H-18 masts & can ship. Pete

Sails were designed by Chip Buck at Whirlwind. We wanted to keep our same DPN number and we certainly don't need more (sq-top area) on our 15 mile re...

Ordered a prototype square top last season for my Prindle 18 with the same area as original sail. It was definitely faster and all the guys complaine...

Totally unnecessary and will add at least 40# to a 375# boat, not to mention the cost. Think about the beach handling--sliding a heavier boat up & do...

Big Bear cost $500/6mo for mast up storage on the beach. Permanent race marks & races every weekend. Pete

Forget it, Peter. The estimated shipping to Albany from San Diego is $640. Could sell you one of my woodies or a Panthercraft disassembled on a narr...

Pete K, need an address with zip code. Pete

Have a nice pair of Sailcraft of Canada hulls. I'll take me a few days to measure, weigh, and get shipping quote. Pete

Have mast, can ship for $500 total to upstate N. Y. Pete

If you want to be more positive, back off the bolt & put another washer under bolt head. You may find that traveler does not pass the head of the slo...

3/16, but they're tough to drill out. Quicker way is to use cut-off grinder & cut off the 1" stopper portion, rounding the sharp corners as well. ...

3/16, but they're tough to drill out. Quicker way is to use cut-off grinder & cut off the 1" stopper portion, rounding the sharp corners as well. ...

And yes get the $4 doggy screw in anchors & screw in below the surface so no tripping over them & tie the boat down. Else I'll make some more money s...

For the Tornado, I lay 3 rows of 3 each. That gives a platform of 24 x 12 which allows you to run it up beach & turn head to wind to drop sails, then...

Buy 4 x 8 sheets of white plastic fence lattice at Home Depot and 12 x 16' blue tarps at Costco or Sams. Lay a tarp down (to keep the sand out), then...

Damon, your surprise is shared by many. Cat sailors look at their solid hulls, good tramps, & colorful sails and put a value on them cumensorate with...

Wasn't rocket science, just cut tube in half & put 3' floating tube inside with black marks denoting 8', 8.5', & 10' widths. Pete

Picked up one last Fall without a mast or tramp. It has Prindle base so am having Chip Buck Sq top the sail to fit the P-16 mast which is one foot sh...

Will be back in Calif in couple weeks & have couple good H-18 hulls available in Big Bear. Pete

You probably have a pre-'79---look on the transom of starboard hull and you'll see vertical digits starting with sur. Numbers near end will be the y...

Certainly. Thicker line bears on the sidewalls of the crummy Seaway blocks causing slower release of sheet in a puff. Use Tornado blocks if they're ...

Restoring one here on the beach in LA Paz as we speak. Easy job. Check first for soft spots on deck in front of main beam and describe size if there...

Totally agree. Learn to sail the boat fast by staying back in heavy air, forward in light air (especially), and having main sheet cleat angle at corr...

Drill a second hole in bottom of rudder pintle if it's popping out. Mast could be raked back a little, but for sure use the jib to solve tacking prob...