I made my crossbar with 3/4" & 1" schedule 40 aluminum pipe. The 3/4" sleeves into the 1" just right. I used pointed Allen key set screws to secure th...

I trail with the mast track down and base forward The mast rests on keel rollers which are mounted to mast supports for and aft that are attached dir...

There are power lines paralleling three highway bridges on that lake that I saw on Google Maps. It's possible to have lines low enough that the mast o...

In VA trailers are titled and tagged. Non powered watercraft of our sizes are not titled. I have titled and tagged two cat trailers as homemade by app...

You can always call Tom at Aquarius and get new rigging from the factory. West Marine's rigging shop in Annapolis looks to know what their about. Fawc...

Well when dipping into a site like that it's always a good idea to wear your rubbers.

My anti virus lit up during the post race coverage and stopped some kind of embed. I don't have the details because it crashed Avast. It might have be...

This link will give you hi-def live video/blockquote> Thanks, worked great. It did try to sneak in a bug, however.

I'm voting Isotope. I have that same trailer. Mine has crossbars and rollers. I'm not so sure about using the fenders for support.Edited by gahamby on...

then you can use masking tape and newspaper to protect exposed areas from drips. Otherwise, just wipe I'm gonna have to go ahead and disagree with yo...

He also doesn't know its an H17.

Anything you put into a scratch is going to hinder gel coat adhesion to some extent. You will never be able to get all the wax out of the carbon fiber...

Get the matching gel coat color, some styrine to reduce the gel coat, some acetone for clean up and one of those Preval aerosol bottles. Also get blue...

ARRRRGH!

Wanted to insure no-one worried about righting the boat due to heavier than average mast weight as the halyard releases on a Supercat take most of tha...

MN3 wrote: With the proper rig you can raise the mast single handed. what do you mean? I was referring to a mast raising rig. Not the standing rigging...

I went with the Krylon for plastics primer and gloss white on my old plastic rudders on the '84 H14T They look fine.I touch up the scratches with glaz...

As the owner of a SC15, I'm biased. Go for the SuperCat17. The mast is bigger in section so it will float,when watertight. This helps avoid going tur...

Just got my super kit Do you mean A Super Cat 19? It's all in the link below. I wanna hear the story to!

Do these flip your switch?

I'm wondering if any specific tolerances apply to the nicopress assembly? Nicopress makes a "go no go gauge" for checking the pressed sleve. If you a...

That works for a mast that goes up facing forward like the H16 pictured. If your mast steps in a rotated position using the forstay presents a problem...

That's a sad sight. I contacted the seller and advised a few edits to his ad.

the hole is way too narrow for the line, and the line needs to go through around 2 inches. If the hole is to narrow for the line perhaps a thinner lin...

Start with the classifieds right on this site. E Bay has tons of listings Then of course: If you get to the Outer Banks via The Wright Memorial Bri...

I have a Spinlock, It's not USCG approved. It works well. I carry an approved spare for formality's sake. Here is an example.

I Googled this: Beach cats in the Turks and Caicos Islands. Go the the Images link. It's all Waves and Getaways but there might be something...

BTW, is there something wrong with me if I LOVE browsing cleats and blocks mischuge Yes, you own an old beachcat! There is no hope.

I had West Marine order me a 212 and 214. Seadog messed up the order but made it right with a free drop ship. It would be nice if Seadog just retailed...