I was able to get 4 concrete "plugs" from a concrete cutting company. These plugs are 20" round and 8" tall with a hole through the center. The plugs...

I was able to get 4 concrete "plugs" from a concrete cutting company. These plugs are 20" round and 8" tall with a hole through the center. The plugs...

I install a 14" round X 10' long aluminum spiral pipe on my Hobie 21SE trailer back in 1989. Built myself two end caps, one that is sealed made as an ...

I have used my Cat Trax since new in '89.....well worth the cost. One flat tire repair in 31 years...... 😉

I guess for a pile of parts it's OKEdited by bill40421SE on May 11, 2020 - 12:33 PM.

I am thinking....a white 1970 Buick Wildcat convertible with a red interior and a Hobie Wild Cat... 😉

Whirlwind sails made me a red new snorkel out of Sunbrella for my Hobie 21SE when I ordered a new jib. It works great! Thanks Chip.

My Hobie 21SE is still resting in its' winterized state. It would take me most of a day to have it ready to trailer to our sailing club (Lake Monroe S...

Back in the later 90's, my kids were young. I did not want to discourage them from sailing on high wind days. So I had Randy Smyth design me a "storm"...

Tim, Thanks for the update. Salty Dog has taken care of me since '89..... 😎

It looks like SLO Sail and Canvas mades a nice vinyl tramp for $400 for the upgrade thread in four different colors.

2019 'Round the Island 60/40 Fort Walton Yacht Club FINAL RESULTS 22 September 2019 Overall Sailed: 2, Discards: 0, To count: 2, Entries: 15, Scoring ...

I only store my sails in their tubes once they are dry. So, there is no ventilation on my setup.

I built my mouse proof sail tube on my 21 trailer out of 14" round aluminum spiral tubing 30 years ago. Strong enough to lightly step on. For my 16 ...

Sometimes while raising my main sail, it seems to jam near the top....what happens, is that the halyard line goes through a small block at the base o...

I understand there will be a small fleet of Hobie 21SE sailing in this event...wish I was on my way there...Thanks for the invite Ted. 😉

For the last 30 years, I have done business with Don @ Salty Dog. He was always the most helpful and quick to handle whatever I needed. He once wo...

I towed my 21 wide for over 20 years plus and only "bumped" a toll booth basket on the Ohio Turnpike. By saying bumped I mean knocked it completely ...

I am able to sail windward with my new spinnaker so I am OK with whatever windage I encounter when it is furled. The range this works in is huge. Th...

Thanks Mac, I have that system now on my 21SE and it works flawlessly. Now I can easily remove my continuous furling line with the mast still up. ;...

outboard/inboard bearing strap kit # 321 30001 😉 These rivet to the both the front and rear crossbar. If my memory serve me right, you will n...

I would not recommend trying to weld in such close proximity to fiberglass. Anodized aluminum is difficult to weld in the first place but the real pro...

I just installed two 8" Hobie hatches that look this those on my 21. They look great and no more sand stuck in the threads of my old screw in type acc...

Martyr, Have you try to launch at the Chicken Bone ramp right before the entrance to Fort Pickens ? I have used that spot in the pass with my kids...

Hey Chuck, I trailer my mast with the comtip riding just on the rear mast caddy to bear it's weight. This way the comtip is supported but doesn't car...

Is your boat a Stars and Stripes edition with gunsmoke blue hulls and a very light gray deck?

Nice setup with the wings....they look very comfortable.